| MOQ: | 1 PCS/20 Tons |
| Price: | $1300-3000 |
| Standard Packaging: | Customized based on project |
| Delivery Period: | 30-60 Days |
| Payment Method: | L/C,D/A,D/P,T/T |
| Supply Capacity: | 15,000 t / month |
An economizer support steel structure is not a light warehouse frame painted grey. One side sits in ambient plant air; the other carries a boiler bank heating up to 350 °C or higher. If both ends are welded rigid, thermal expansion bends the columns before the boiler even reaches full load.
Ordinary structural steel expands by 12 * 10⁻⁶ per °C. Across a 4 m wide economizer module rising by 300 °C, the casing grows by roughly 14.4 mm while the external support frame stays near ambient temperature.
Making the H-section columns heavier does not absorb 14 mm of forced movement — it simply drives higher horizontal shear into the anchor bolts and gusset plates. True anti-deformation design sets one fixed point to resist wind, seismic and duct thrust, then installs slotted-hole guides or low-friction sliding bearings at the remaining supports so the casing expands freely without pulling the frame out of plumb.
This is the same thermal and differential movement logic used on a long steel connecting corridor, except here the temperature swing happens on every boiler start-up and shutdown cycle.
Reference listings often pair carbon steel with a “-20 °C to 550 °C" label without stating where that temperature sits. Structural carbon steel such as Q355B or ASTM A572 Gr.50 retains normal yield strength near ambient conditions, begins losing yield strength noticeably above 300 °C, and enters creep above 450 °C.
A dependable economizer support steel structure separates two zones cleanly:
Buying the whole package from one fabrication drawing without separating cold steel from heat-resistant steel creates sagging brackets inside the flue within the first operating year.
Vertical gravity from the economizer tubes and water inventory is only the starting load. Three plant realities govern member sizing and weld detailing on boiler support frames:
Most boiler economizer support steel structure assemblies mix rolled or welded H-section steel columns with stiffened bearing girders and angle/channel cross-bracing. Column web stiffeners sit directly beneath each saddle or hanger load line so concentrated reactions do not cripple the flange locally.
Plates and gussets are CNC profiled to ±1.0 mm cutting tolerance, weld preparations are bevelled for full-penetration joints where loaded in tension or fatigue, and primary multi-bay bents are trial-assembled in the shop on jigs before blasting. Trial fit-up catches anchor-bolt pitch mismatches and slotted-hole binding before steel leaves for the power station.
Power-plant outages and new-build boiler erection run on crane windows. Shipping loose bundles of unpainted, unmarked steel shifts sorting work onto high-rate site fitters.
Every column, tie beam, saddle and gusset in our economizer support steel structure supply is hard-stamped and waterproof-tagged with its shop drawing piece mark, erection level and bay number. Long H-section columns and braced frames travel in steel-strapped bundles with timber dunnage inside 40 ft open-top or flat-rack containers; gusset plates, PTFE slide pads and anchor assemblies travel in labelled steel crates matched one-to-one with the container packing list.
We fabricate the steel economizer support steel structure, bracing, platforms, anchor-bolt templates and shop erection drawings from your project engineering input. Boiler pressure tubes, refractory lining, expansion joints, civil foundations and local erection labour are by others unless agreed separately.
Send the items below for an accurate take-off and fabrication quote:
The external frame sits outside the insulation and operates near ambient temperature using Q355B or S355JR structural steel. Internal hangers and flue guard plates exposed to 300–550 °C gas require heat-resistant alloy grades or thermal isolation pads to prevent high-temperature creep.
Thermal expansion of a heated economizer casing — about 14.4 mm across a 4 m span at a 300 °C rise — generates massive horizontal force if welded rigidly at all supports. Fixed-plus-sliding bearing seats are required so thermal growth releases without bending the columns.
Full-size multi-ton support bents cannot be couriered as samples. For technical verification before bulk fabrication, we provide raw material mill test certificates (EN 10204 3.1 MTC), weld procedure and coupon records, and live video inspection of shop trial assembly.
We regularly fabricate from Q235B and Q355B as well as equivalent ASTM A36, A572 Gr.50 and EN 10025 S275JR / S355JR sections. Shop fabrication follows CE (EN 1090-1), ISO 9001 and project-specified AWS D1.1 or GB 50205 tolerances.
Critical full-penetration hanger and splice joints undergo 100% visual inspection plus ultrasonic testing (UT) or magnetic particle testing (MT) to the percentage defined in your contract ITP. Third-party inspectors from SGS, BV or TÜV are welcome to witness NDT prior to blasting.
Standard-length beams under 11.8 m fit inside 40 ft high-cube or open-top containers; wider welded box bents or pre-assembled frames ship on 40 ft flat racks or breakbulk vessels. For harsh coastal plants, see our industrial steel structure workshop coating specifications.
Send your structural drawings or BoM, thermal operating conditions, NDT percentage and destination port. Our engineering estimating team reviews the fabrication details and returns an itemized weight take-off and quotation.