| MOQ: | 1 PCS/20 Tons |
| Price: | $1300-3000 |
| Standard Packaging: | Customized based on project |
| Delivery Period: | 30-60 Days |
| Payment Method: | L/C,D/A,D/P,T/T |
| Supply Capacity: | 15,000 t / month |
UNS S17400 • Condition A / H900 / H1025 / H1150 • AMS 5643 • ASTM A564
17-4PH is bought by condition, not by grade. The same heat can leave the mill at 30 HRC and soft enough to machine, or at 44 HRC and hard enough to resist wear — and the difference is a four-hour ageing treatment, not a different alloy. Most quotation problems on this material start with a buyer asking for "17-4PH" without specifying which condition.
630 is the common designation for 17-4PH, a martensitic precipitation-hardening stainless steel: nominally 17% chromium, 4% nickel, 4% copper, with niobium. It is also written as UNS S17400, AISI 630, SUS630, or 05Cr17Ni4Cu4Nb in the Chinese system.
It is not a rare metal, and it is not 15-5PH. Those two confusions appear on supplier listings often enough to be worth stating: 15-5PH is UNS S15500, a different alloy with higher toughness and better transverse ductility, and it costs more.
Material is supplied either solution-treated (Condition A) or solution-treated and aged to one of the standard conditions. Hardness and strength move together.
State which condition you need at the enquiry stage. Supplying Condition A to a drawing that calls for H900 is not a small error — the part will not hold its tolerance after machining, and it will not wear.
Valve stems and bodies, pump shafts, gears and splines, moulds and die inserts, aircraft fittings, food-processing equipment, and surgical instruments — anywhere the part needs high strength, reasonable corrosion resistance, and dimensional stability after heat treatment.
It is a poor choice for continuous service above about 300 °C, and it is not a substitute for 316L in a chloride-rich environment where stress corrosion cracking is the governing risk.
Machine in Condition A wherever the geometry allows, then age to final hardness. Machining at H900 is possible but slow, and it wears tooling.
Welding is done in Condition A, followed by a full solution treatment and ageing, or by a local ageing treatment where the procedure allows. A welded joint left in the as-welded condition has neither the strength nor the corrosion resistance of the parent metal.
| Condition | A, H900, H1025, H1150, H1150D |
|---|---|
| Product form and size | Plate thickness × width × length, or bar diameter |
| Standard | AMS 5643 for aerospace, ASTM A564 for bars, ASTM A693 for plate |
| Test | Hardness, tensile, and any impact requirement |
| Certificate | EN 10204 3.1, with the heat number and the ageing record |
| Surface | Rolled, pickled, or polished |
Send the form, the size, the condition and the standard. For plate, give thickness × width × length and the quantity in pieces or kilograms. For bar, give diameter and length. If the part is to be machined after supply, say so — Condition A is usually the right supply condition, and it is priced differently from H900.
We return the mill certificate, the heat number and a quotation.
Yes. 17-4PH, UNS S17400, AISI 630 and SUS630 all refer to the same alloy. The designation changes with the standard, not the steel.
15-5PH (UNS S15500) has 15% chromium and 5% nickel instead of 17/4, and gives better toughness and transverse ductility. It is a different alloy and a higher price.
Condition A if you are machining the part and ageing afterwards. H900 or H1025 if you need the strength in the supplied material. H1150 where toughness matters more than strength.
Yes, but H900 at around 44 HRC is slow to machine and hard on tooling. Most parts are machined in Condition A and aged to finish.
It is better than 400-series stainless and worse than 316L in chloride environments, and it is susceptible to stress corrosion cracking at high strength. For marine service, specify H1150 and have the environment reviewed.
EN 10204 3.1, tied to the heat number, with the ageing record for the condition supplied.
Around 500 kg for plate or bar from stock sizes; smaller quantities are possible from cut plate, and are quoted case by case.
Send the form, size, condition and standard. We return the certificate, the heat number and a quotation.